2 RS485 COM Ports Integrated HMI PLC MView Software High Speed Counting
|Program Port||1 TYPE-C, 1 RS232 ()||DI/DO||Max 12DI/12DO|
|High-speed Counting||Single Phase 6 Channel 60KHz, Or 2 AB 60KHz + 1 AB 10KHz||High-speed Pulse||8 Channels, Y0-Y3 Is 100KHz, Y4-Y7 Is 10KHz.|
|HMI Software||MView HMI Programming Software||PLC Software||GX Developer 8.86 And WORKS 2|
2 RS485 Integrated HMI PLC,
COM Ports Integrated HMI PLC,
MView Software PLC HMI Panel
Integrated HMI PLC 2 RS485 COM Ports MView Software High-Speed Counting
|Feature||60K-color resistive touch screen, supports portrait display|
|ROM||NOR Flash 8MB|
|CPU||32bit CPU 408MHz|
Input: Passive NPN, public terminal isolated
Transistor output: Low level NPN, COM connect to negative; Relay output: Normally open dry contact
|DO type and load||Relay MR/MOS tube, MOS tube: 2A/point, 4A/4 point COM, 5A/12 point COM; MR: 2A/point, 5A/12 point COM.|
|AI type (optional)||
Thermocouple E/E_/K/K_/S/S_/T/T_/J/J_ / PT100/ PT1000/ NTC10K/ NTC50K/ NTC100K/
0~10V/ 0~5V/ 0~20mA/ 4~20mA/ mixed
|AO type (optional)||0~10V /0~5V/ 0~20mA/ 4~20mA/ mixed|
|High-speed function||High-speed counting||
Single phase 6 channel 60KHz, or 2 AB 60KHz + 1 AB 10KHz,
or 2 ABZ 60KHz + 1 AB phase 10 KHz
8 channels, Y0-Y3 is 100KHz, Y4-Y7 is 10KHz.
High-speed counting + high-speed pulse < 480KHz
|Connection||HMI||Type-C HMI download port (can download PLC program through the USB penetrating function), RS232 port|
|PLC||1 TYPE-C, 1 RS232 (program port)|
1 RS485 or 2 RS485 COM ports (one of which is changed from the default RS232 port);
1 WIFI (occupy default RS232 port)
|Software||HMI||Coolmay mView HMI Programming Software|
|PLC||Compatible with GX Developer 8.86 and WORKS 2|
Support Y0-Y7 total 8 channels (please select transistor MT output);
There are no restrictions on pulse width and cycle, both in milliseconds (ms).
Special customized PWM-analog output port
The following parameters need to be provided during customizing selection:
The output voltage of the required PWM;
The output frequency of the required PWM;
Confirm the number of customized PWM, up to 4 channels of PWM can be customized (specifically, it depends on the number of analog outputs of the model selected by the customer).
Customize whether PWM coexists with other analog quantities. (If the product is additionally equipped with analog, analog output terminals DA0~DA3 are a group, DA4~DA7 are a group. When QM3G customizes PWM, the output frequency can only be installed with other analogs in a group when the output frequency is only 21KHz ).
mView provides the function of simulating directly on the PC. You can use this function to simulate the actions performed on the HMI after planning HMI. On the one hand, it increases the convenience of finding program errors, and on the other hand, it can save downloading to the time HMI can connect to the controller. The simulation function of mView is divided into two types: [On-Line Run] and [Off-Line Run], as shown in the figure below.