10.1'' TFT 24DI 20DO HMI PLC All In One 32K retentive register
|Features||Support Interrupt, Linear Arc Interpolation, PID Auto-tuning||Dimension||275*194*36mm|
|CPU||CORTEX A8 720MHz-1GHz||Analog I/O||16AI/8AO|
|DI/DO||24DI/20DO||Protocol||Programming Port Protocol/Modbus Protocol/Rs Protocol/BD Board Protocol|
10.1'' HMI PLC All In One,
32K HMI PLC All In One,
10.1'' plc touch screen
10.1'' TFT 24DI 20DO HMI PLC All In One 32K Retentive Register
HMI PLC All In One 24DI/20DO 32K Program Capacity Supportlinear Arc Interpolation And PID Auto-Tuning
Introduction of each interface and indicator
POWER: Power indicator, connected to the power light
RUN: PLC running status indicator. This light is on when the PLC is running.
COM: touch screen and PLC communication status indicator, when the two communicate, the light is on
Power terminal: The positive and negative terminals of the DC24V switching power supply are respectively connected to the DC24V and 0V of the power supply terminal.
PLC programming port: two PLC programming ports (MiniB type usb port / RS232), PLC program can be downloaded through 232 programming line or USB cable download
Touch screen programming port: download touch screen configuration program
USB interface: mainly can be directly inserted into the U disk of the file system FAT 32, can also be inserted into the mouse.
|Features||Support interrupt, linear arc interpolation, PID auto-tuning. 32K program capacity, 32K retentive register|
|CPU||CORTEX A8 720MHz-1GHz|
Input: Passive NPN, public terminal isolated
Transistor output: Low level NPN, COM connect to negative; Relay output: Normally open dry contact
|DO type and load||
Relay (MR) or transistor (MT, Y0-Y3 are MOS) or mixed (MRT)
MOS tube: 2A/point, 4A/4 points COM; MT: 0.5A/point, 0.8A/4 points COM, 1.6A/8 points COM; MR: 2A/point, 4A/4 points COM, 5A/12 points COM.
|Analog I/O (optional)||Max 16AI/8AO|
|AI type (optional)||
Type E/E_/K/K_/S/S_/T/T_/J/J_ thermocouple/
PT100/ PT1000/ NTC10K/ NTC50K/ NTC100K/
0~10V/ 0~5V/ -5V~5V/ -10V~10V/ 0~20mA/ 4~20mA/ mixed
|AO type (optional)||
0~10V /0~5V/ 0~20mA/ 4~20mA/ mixed/
-5~5V/ -10~10V (2DA for 1 minus voltage)
|High-speed function||High-speed counting||6 channels single-phase 60KHz, or 2 channels AB (Z) phase 60KHz + 1 channel AB phase 10KHz|
8 channels,Y0-Y3 is 100KHz, Y4-Y7 is 10KHz.
High-speed counting + high-speed pulse < 480KHz
|Connection||HMI||1 HMI download port,1 USB 2.0 port|
1 RS485 or 1RS232 port
Ethernet port (can not coexist with PLC Ethernet port)
|PLC||1 Mini type B USB port, 1 RS232 port (Program port,also can be used as COM port)|
|1 RS485 or 2 RS485 COM ports (one is changed from the default RS232 port), CAN (2.0A/B), Ethernet port (can not coexist with HMI Ethernet port), WIFI (will occupy the default RS232)|
|Software||HMI||CoolMayHMI HMI programming software|
|PLC||Compatible with Mitsubishi GX Developer8.86 and GX WORKS 2|
◆ Upper computer programming software compatible with Works 2/GX Developer8.86 (supports Ladder diagram and SFC language, does not support structured programming/labels).
◆ Powerful, compatible with FX3G/FX3U/FX3S PLC, high processing speed.
◆ Military level 32 bit CPU adopted, which is faster and more adapted to industrial environment of high electromagnetic interference.
◆ Special encryption, prevent illegal reading thoroughly. 8-bit encryption, 12345678 as password can thoroughly prevent reading of ladder logic program.
◆ Clock supported, rechargeable battery adopted.
◆ Default With 1 HMI Downloading port, 2 PLC programming ports: one MiniB USB port with faster downloading speed; one Rs232 programming port with 8 mouse hole sockets, and 1 USB port.
◆ Support programming port protocol/Modbus protocol/Rs protocol/BD board protocol,
PLC communication with each other and other devices is easily achieved.
PLC Programming notice
The PLC is compatible with GX 8.86/Works 2 and below. If you use other versions of the software, incompatibility may occur.
When the PLC program is downloaded, there is a prompt error: Cannot specify the com port,
GX 8.86 software: Online - Transfer settings change com port;
Works 2: All targets - Change the com port in all connected targets;
If communication error occurs, cable is abnormal If prompted, remove it by powering off, detecting the cable, detecting whether the power is normal, or replacing the computer.